As my designs show, my plan is to connect the 2 pontoons using 2 box sections and a deck. Below is a detailed design of the box section, showing 3 bulkheads and openings for storage.
My initial plan was to make the sections using 18 mm plywood. That would be plenty strong I think. But it would also be plenty heavy. So I’m considering using 9 mm plywood. Or maybe use 18 mm for the verticals and 9 mm for the horizontals. But can I get away with that?
How much strength do I need?
The pontoons will weigh around 100 kg each when finished. I plan to use them for storage when underway and I will probable have one or two batteries on board. Let’s say the total weight of each pontoon could be anything up to 200 kg.
Total width of the boat, and therefor the box sections, is 2 meters.
In an extreme scenario one pontoon might be in the water and one might be suspended in mid air, for whatever reason. That means each box section need to be able to carry 200 kg / 2 (box sections) = 100 kg as an absolute minimum. To account for dynamic loads, I would like a safety margin of 100%. So each box section needs to be able to carry 200 kg at 2 meters length.
Anyone care to help me calculate / guesstimate the minimum required wall thickness?
Here is the latest iteration of my catamaran design. I’m still not sure what I will do for cabin, but I guess I’ll figure that one out as I go along.
I’ve added some additional braces under the deck (the deck will be 18 mm). I’ll probably add a 45 degree panel from the underside of the deck to the side of the hull to make the entire structure more rigid.
Another change from previous designs is that I moved the front cross member forward, against the front bulkhead. This will increase cabin space dramatically. The net between the bows should make a nice place to sit and enjoy the water 🙂
While driving home from work, I was thinking about how to secure stuff stored inside the hulls. What if I have some supplies, batteries and whatnot on board? I don’t want everything sliding back and forth while sailing. I need something to tie stuff to…
So I drilled some 5 cm holes in the bulkheads. This gives me something to attach a line to. Ideally I should also have attachment points along the length of the hull. Not sure how I should go about that. Suggestions are welcome!
This weekend the bottom of the first pontoon was closed and she could be turned upright. Another milestone 🙂
I’ve also started work on the second pontoon. The glued together sides are on the garage floor. Bulkheads are done already, so I should be able to start gluing her together next weekend. It’s going to be a crowded garage.
Next is filleting all the joints. It’s pretty hard to get epoxy thick enough so it doesn’t run. I need to add about 10% filler material, measured by weight (150 g of epoxy needs 15 g of filler). That makes it so thick it’s hard to mix. In the end I kust checked every few hours and smooth out any runners. Not perfect, but good enough for me.
I’ll put injection resin on the inside to make the wood waterproof. I may also paint the inside, haven’t decided on that yet.
After work I don’t have the time and energy to take on large projects. But i try to make a little progress every day. Yesterday I tweaked my design a bit in Sketchup, making the thing fit in my garage. Today it was making a second bottom piece:
After lots of thinking and designing, the time has finally come to make some sawdust and see if I can actually make my ideas a reality.
This pile should be enough for both pontoons + parts of the middle deck. I’m not sure what to do with the cabin, so I’ll get wood when I get to that part.
Laying out and connecting the planking for the sides of the first pontoon. I made the connection with a simple butt join and glued a piece of plywood on top of the butt. Not the prettiest, but should be plenty strong for what I need.
Sawing the bulkheads sure makes a lot of dust. I cut bulkheads for both pontoons. Hope I got the numbers right 🙂
Just follow the plans…
I will round off the edges and add a few layers of glass later. Should do the job. The front section, up to the first bulkhead, will be sealed permanently for make an air tight chamber. I wonder if I should fill it with foam or something else? I will impregnate the wall inside and out with epoxy.
That actually went a lot easier than I expected. I dreaded having to adjust the curvature multiple times, but somehow it fit on the first try. Very happy with the results 🙂